Skip Navigation Website Accessibility
 

Radial ProD8 - Passive Direct Box, 8 channel, 19" 1RU Rack Mountable

   
Quantity:    
UPC:8001120
Sku:PROD8

Add to Cart

Passive 8-Channel Rackmount Direct Box

The ProD8 is a high performance 8-channel passive direct box optimized for keyboard rigs in professional touring, with redundant 1/4″ inputs for each channel and a completely passive design that requires no power to operate.

The Radial ProD8 is an 8 channel 19″ rack-mountable direct box designed for professional concert touring. The feature set has been optimized for keyboards but as with any direct box, it is certainly suitable for use with instruments or playback systems. The passive signal path incorporates a custom wound Eclipse ET-DB2 transformer and RF filtering that is able to withstand excessive signal levels without distortion while delivering a linear response across the audio spectrum.


  • High density 8-channel rackmount DI for keyboards
  • Reversible rack ears to optimize patching setup
  • Withstands extreme dynamics from high-output sources
  • Redundant inputs let you incorporate a backup system


Specifications 
Audio circuit type: Passive, transformer based
Transformer: Eclipse ET-DB2, 12:1 ratio
Number of channels: 8
Frequency response: 20Hz ~ 18.5KHz (± 0.2dB)
Dynamic range: 128dB
Total harmonic distortion: 0.01% from 20Hz~20kHz @-10dB
Phase Deviation: 1° @ 100Hz; 8° @ 20Hz
Input Impedance: 140k Ohms, unbalanced
Output Impedance: 150 Ohms, balanced
Maximum Input: +18dB @ 20Hz
Features
Input pad, 180° polarity reverse, Ground lift
Input Connectors: 1/4"
Output Connectors: XLR
General
Construction: 14 gauge steel chassis & outer shell
Size (L x W x D): 19" x 6.25" x 1.75" (48.3cm x 15.875cm x 4.45cm)
Weight: 7.2lb (3.26 kg)
Shipping size (L x W x D): 22" x 10.375" x 4.5" (55.9cm x 26.4cm x 11.4cm)
Shipping weight: 8.30lb (3.76 kg)
Power: Passive, no power required
Conditions: For use in dry locations only between 5°C and 40°C
Warranty: Radial 3-year, transferable


Professional performance

The ProD8 features up to 8 direct box outputs in a single 1RU rack space for professional touring, with dual ¼" inputs on each channel to incorporate a backup system or connect up to 16 channels of audio at once. A ¼" TRS effects insert jack on each channel allows for connection to various effects devices while adding greater routing options, while a thru-put jack delivers a direct feed to the artist's playback system. The front panel features isolated XLRs for balanced low-noise outputs, each equipped with ground lift and 180° polarity reverse switches.

Transformer driven for greater headroom & low noise

The engine inside the ProD8 is a custom wound Eclipse ET-DB2 transformer that performs both the impedance matching and balancing. Linear from 20Hz to 20kHz, it is able to withstand the extreme dynamics common with today's digital keyboards. Unlike active circuits that overload and square wave when the rail voltage is exceeded, transformers saturate. This means that as the signal increases, the ProD8 naturally rounds out the tone producing a warm Bessel curve reminiscent of the very best vintage audio gear. The other significant advantage to this passive design is 100% galvanic isolation between the source and destination, which eliminates hum and buzz caused by ground loops.


Adaptable Configuration

To enhance setup options, the Radial ProD8 is equipped with reversible rack ears. This handy feature allows the system tech to position the inputs on the front of the rack when interfacing with external keyboards or have them inside if the setup is predominantly equipped with rack modules.

ProD8 Applications

The ProD8 in the Studio

Set the ProD8 rack ears so that the ¼ inputs are on the front panel to make patching different instruments easy. This give you access to the dual inputs and thru-put jacks for quick connection to amps in the studio.

The ProD8 with Rack Synths

Set the ProD8 up with the XLR outputs facing front to accomodate touring racks of modular synths. With the ¼ inputs on the inside of the rack your synths stay connected while sound techs patch the XLR outs into the main snake and PA system.

Using the ProD8 for Backing Tracks

The ProD8's dual summed inputs make it convenient for patching two sources into each channel at the same time. This lets you use the ProD8 for backing tracks with two multi-track running in sync or redundant keyboard setups for live performances.